🛠️ What Have You Done To Your LC250 Today?

[PurelyAbrasive]

Today has been productive. I finished the wiring to my CB and distribution blocks. I am waiting on some wire so I can finish pre-wiring my relay/fuse box. Over all I think the wiring turned out really well. I measured all the cable lengths and had a local battery cable company make them for me. I will probably get some liquid electrical tape and put on the CB terminals for more insulation.

 

[EOD Guy]

Today has been productive. I finished the wiring to my CB and distribution blocks. I am waiting on some wire so I can finish pre-wiring my relay/fuse box. Over all I think the wiring turned out really well. I measured all the cable lengths and had a local battery cable company make them for me. I will probably get some liquid electrical tape and put on the CB terminals for more insulation.

I use these on the exposed studs vs the rubber caps.

https://www.amazon.com/Terminal-Insulating-Protector-Replacement-Commercial/dp/B08VWTZ6Q4/?tag=landcruiserforum-20

 

[t3lcfe]

Today has been productive. I finished the wiring to my CB and distribution blocks. I am waiting on some wire so I can finish pre-wiring my relay/fuse box. Over all I think the wiring turned out really well. I measured all the cable lengths and had a local battery cable company make them for me. I will probably get some liquid electrical tape and put on the CB terminals for more insulation.

Looks great

 

[jptruck]

Little interior improvement happening. This is the start, but it's going on all 4 doors, floor pan and rear hatch. Straight replacing the JBL speakers (which don't sound horrible, but are just plastic) with something a little better.

 

[shwazz714]

Little interior improvement happening. This is the start, but it's going on all 4 doors, floor pan and rear hatch. Straight replacing the JBL speakers (which don't sound horrible, but are just plastic) with something a little better.

View attachment 29113

Very nice - what’s that cost to get done? Would like to do it as well.

 

[MtnLC]

Installed a new mud flap. Much better coverage than stock for these wheels and tires. Three more to go.

Before:

View attachment 28838

After:
View attachment 28839View attachment 28840

Are those the Original or XL Rokblokz?

 

[Markarian421]

Are those the Original or XL Rokblokz?

Original

 

[jptruck]

Very nice - what’s that cost to get done? Would like to do it as well.

Material is about $400 for the soundproofing. The speakers replacement are whatever you want to spend, but I'm in just under $1,200 for dash (2), doors (front and back) and tweeters. Will add a new sub if that's not enough. Leaving center speaker alone. Labor depends on whether you do it or have someone do it, but I'm paying a pro $600 to do it. Probably 12 hours of labor.

Did this primarily for the sound deadening aspects. LC is not loud, per se, but it'll be a lot quieter after this.

 

[shwazz714]

Material is about $400 for the soundproofing. The speakers replacement are whatever you want to spend, but I'm in just under $1,200 for dash (2), doors (front and back) and tweeters. Will add a new sub if that's not enough. Leaving center speaker alone. Labor depends on whether you do it or have someone do it, but I'm paying a pro $600 to do it. Probably 12 hours of labor.

Did this primarily for the sound deadening aspects. LC is not loud, per se, but it'll be a lot quieter after this.

Awesome excited to hear how it goes.

I love my LC and would love to make it even quieter in the cabin. This is an investment I’d be willing to make depending on feedback on results.

 

[MandRautomotive]

Did a install of a Ham Radio and VHF/UHF Antenna using @MandRautomotive ditch light brackets:

Ham Radio Operators...

Do you know what the face plate part number is? sorry, I haven't run across it yet.

www.landcruiserforum.com

Please post some photos. Would love to see it.

 

[teghogh]

Today got me some sliders at some local place. Mine's the white one

Is the black lc a wide body ? Can’t figure out why the fenders stick out so much

 

[highsmith]

Please post some photos. Would love to see it.

You can see photos in the Ham Radio thread: Ham Radio Operators...

 

[thurchik]

Installed skid plates. Produced by local company. 3mm. steel zinc coated.
$314 parts+labour

 

[PurelyAbrasive]

Rago Ditch Light Brackets was on the todo list today. Waiting on the ditch lights now.

 

[Alpha Puppy]

Rago Ditch Light Brackets was on the todo list today. Waiting on the ditch lights now.

Uuuff, not loving those exposed round screw heads...

 

[amzazai]

I added a magsafe wireless charger where the premium/fe wireless charger is. Attached with double stick tape so it holds my phone securely in that spotView attachment 23408View attachment 23409

 

[t3lcfe]

Uuuff, not loving those exposed round screw heads...

Agreed

 

[bbrhm]

Material is about $400 for the soundproofing. The speakers replacement are whatever you want to spend, but I'm in just under $1,200 for dash (2), doors (front and back) and tweeters. Will add a new sub if that's not enough. Leaving center speaker alone. Labor depends on whether you do it or have someone do it, but I'm paying a pro $600 to do it. Probably 12 hours of labor.

Did this primarily for the sound deadening aspects. LC is not loud, per se, but it'll be a lot quieter after this.

Very interested in outcomes here! (Mostly RE: Deadening, but also speakers tbh!)

 

[JordanJ]

Uuuff, not loving those exposed round screw heads...

Just me, not trying to start anything, but I think they give it a kind of “strong” look… with a steel bumper, winch, ditch lights, roof rack, sliders… full build, balls out… I think it’ll all tie in nicely and look mean. Trail weapon.

 

[EOD Guy]

Agreed

If they're no stainless steel, I'd swap them out. I'd also apply some clear nail polish just in the allen key opening as impure SS will rust.